Pages

Sunday, March 30, 2014

An 1880s Bustle Dress Construction Tutorial--The Overskirt!

This article originally appeared on Your Wardrobe Unlock'd.

The original dress that this is based on can be seen on my antiques blog, here.

finshed_dress04 finshed_dress05 finshed_dress06

I'm breaking this tutorial up into three parts, the skirt, overskirt, and bodice. The scaled pattern for each part will be at the bottom of the post. There's also another post with the dress actually being worn.



Overskirt

overskirt_base02 overskirt_base03
overskirt_base04

The first steps of the overskirt aren’t truly necessary, but interesting in the history of the skirt. It originally had a center back placket, which was later closed and covered.

Sew the center back panels together, leaving the top nine inches open. Hem the opening with a whipstitch. Next, baste the opening closed. If not trying to copy the original alteration, just sew the whole center back seam.

overskirt_base05 overskirt_base06
overskirt_base07 overskirt_base08
overskirt_base11

The next step is rather necessary--the hem!

First, hem the sides with a 1 ¼” hem. Next, fold the top edge up two inches, and under half an inch. Fold the corner to form a diagonal. Sew the hem by machine. Sew the loose edge of that corner down by hand.

overskirt_base09 overskirt_base10

Fold the top edge over ½ inch and press it. Sew the cords to the skirt.

overskirt_base01

The cords and tapes for lifting the skirt. The base skirt has a twisted cord and narrow piece of selvage. The puff has two strips of fabric folded and whipstitched.

overskirt_puff01 overskirt_puff02

Sew the seams with a ¼” seam allowance. Press the curved edge up about 1 ¼” for the hem. Fold the top under ¼” and pin with lots of pins. You’ll need to ease it a little to accommodate the curve, but with enough pins, it should get pretty smooth. Sew with a machine stitch.

overskirt_puff03 overskirt_puff04

Press the straight edges of the overskirt in one inch.

overskirt_puff05 overskirt_puff06

Sew in the tapes. A confession, these don’t exactly match the original. However, they do look good, and I really didn’t want to redo it! It does show the importance of testing! The draft shows the correct placement of the tapes.

overskirt_puff07 overskirt_puff08
overskirt_puff09

Make the box pleat in the center back.

overskirt_puff10 overskirt_puff11

Pleat the sides of the overskirt. There are five pleats on each side, measuring ½ to ¾ inch. The finished measurement is 7 inches.

overskirt_puff12 overskirt_puff13

Hand baste the pleats into place.

Picture overskirt puff 14
overskirt_puff14

Take the bottom of the pleats and sew to the top of the skirt, ½” away from the top of the skirt.

overskirt_combined01 overskirt_combined02
overskirt_combined03

As it’s easier to sew things flat, mount the puff to the base. Sew the box pleat to the center seam of the base, just at the bottom of the original placket. Sew the pleat into place by hand.

overskirt_combined04 overskirt_combined05

Gather the base skirt. The original was done with a single running stitch through the ½ inch fold. Pleat the puff. The overskirt base is five inches wider than the puff. The gathering on the skirt is uneven--the left side is five inches wider than the right. Match the puff right edge to the base right edge, the centers, and allow the left base side to extend five inches past the edge of the puff.

overskirt_combined06 overskirt_combined07
overskirt_combined08 overskirt_combined09

I made the waistband measure 19 inches, which is 71% of my waist measurement. The waistband of the original is 71% of the waist measurement.

The waistband construction is standard. Place it right sides together to the front. Sew it through to the right side through all layers, fold the edges in, fold the waistband in half, and whipstitch into place.

overskirt_combined10

Sew tapes to the edges of the waistband for closures, and the overskirt is done!

bustle_pattern0



1 comment: